I need all 4, good wheel spoilers and a nice set of front turn signal lamps for my 77.
none of those sorry
400 engine mounts.(engine side), cruise control vacuum servo and cable(400)
dont have these either, now that im using a 400 ill be needing the set if they are on my 400 motor sitting there.
choke stove for 77 a 400. bolts to manifold in exhaust x-over and has 2 tubes which one attaches to choke of carb. any light blue (robins egg blue ) door panels (driver) .
im almost positive the 400 i have has the choke stove on it, and i know it has the manifolds on it, let me check if it has the bolts for the x over, and no door panels, those usually are rotted.....
driver quality nose emblem washer tank lid
no nose emblems, i gotta buy new too, washer tank lid i do have here in md 5$ shipped...
'78 deluxe interior door panels camel
no door panels
im looking for a vent tube for a 400 and sunvisor brackets w/ screws
might have it gotta check the motor
how about a oil/temp gauge, a dust cover for an auto trans 350 on a 403 olds, radio knobs for a stock radio and I dont suppose you have the nut and bolt that keeps the rear end spoilers flat to the body.
have the oil/temp gauge here 20 shipped dust cover is in ohio, 20 shipped no radio knobs, and no nuts and bolts....
Do you have red interior parts and the map pocket for a 79
no red interior parts, but yes on the map pocket 15 shipped....
i need heater parts
not sure the correct name for it
but i need the core housing that bolts to the fire wall on the passenger side under the hood
and i need just about any heater parts you got probally
and also i need the lower dash panel under the steering wheel
pm me thanks
is it for a heat only car if so then no, if its for an a/c car then yes 35 plus shipping, dont know what shipping would cost on that one, as for lower dash panel piece, 10 shipped....
I need the air cleaner assembly for a 78/79 Pontiac 400.
dont have it
I know i'm late, but I could use a wiring harness for my Delco radio!
nope, id reccomend ebay see a few on there from time to time
I need a front/chin spoiler for a '79, as well as a passenger front flare.
got it, 40 plus ship
Aftermarket 3 piece louver.
dont have any
How about the plasitic covers for the chrome seatbelt buckle?
no go on these
holy smokes.
well i need a good pair of front spoilers via 78 and older
I also would like to get ahold of a nice 2.73 posi rear drum or disc
ws6 steering box and sway bars
early 77 6x heads
200R4 trans
76 older shaker
400 choke parts that connect from carb to intake
w72 auto exhaust manifolds
oh and then a really solid coupe body shell
i have a pair of spoilers that were on the front of my car when it had a 78 front end, mounts different than factory spoilers, use speednuts where the normal bracket nuts would go got the 2.73 drum rear, gotta check the part numbers on the steering box, i have 76 6x heads but gotta see if im using them or not, no 200r4 trans, do have a 76 older shaker gotta see if i can get it back from dave, he forgot to send it to me, choke parts im not 100% positive on having gotta check, but they might already be called for by another guy, dont have the w72 manifolds but do have the manifolds on the 76 heads..... and have a 79 body shell, all rust was patched except for the tail panel....floors are done, 1/4s have already been replaced, frame rails patched....interested i can do a good deal for you on everything.....
What do you have for guts of a 1978 ta I need console with window switch dash with a/c door panels and a steering wheel rear deck tray the bottom or the air cleaner and some manifolds. I have a tan or camel interior
have consoles, gotta see whats what, do you need a full dash or just the bezel? i have bezels, have a steering wheel but the foam is a little rough, if y88rick doesnt want the manifolds i have the 76 manifolds, as for colors on everything im almost positive it would need to be dyed....
Did you ever go? I need a Radiator Core support
core supports i have two, both rough on opposite ends, if you are interested i can do the work to splice the two together, professionally by drilling out the spot welds and replacing only what needs replaced, and it would be very nice.....