Author Topic: Rust free sheetmetal (Read 5498 times)

Crzy4my10th · « **on:** January 08, 2007, 06:17:14 PM »

Most the TAC-ers have seen this post but I thought I'd throw it out here as well.

I'm cutting up a nice 80 TA. Available in the near future ( They're still on the car): Rust free floor pans. Extremely clean and will include the toe kicks on the front pans and the rear foot pans for the rears. Fisher T-top roof and a passenger side rear quarter. I can cut these where ever you'd like.

I've also got two other rust free quarters. Both available now and are cut of car. Drivers side has a small crease in the lower rear section. A very easy fix. The passenger side hasn't been preped yet so I'll post it's condition later.

Rust free TA fenders may also be available. I'm debating on keeping them so again, I'll post when I make up my mind. :?

on edit; I have a rust free passenger side floor pan with the toe kick available now. I was going to use it on the TA but we decided to replace the entire floor in one piece instead of spicing it in.

Thanks
David

Eagle 1 · « **Reply #1 on:** January 08, 2007, 08:26:41 PM »

I might be interested in the passenger side quarter.
Let me know what it looks like when you get it out.

Banditboy21 · « **Reply #2 on:** January 08, 2007, 09:27:29 PM »

im interested when u get everything out

Crzy4my10th · « **Reply #3 on:** January 09, 2007, 05:57:22 AM »

Quote from: "Banditboy21"

im interested when u get everything out

What section are you looking for BB?

Thanks
David

Crzy4my10th · « **Reply #4 on:** January 09, 2007, 06:05:07 AM »

Quote from: "Eagle 1"

I might be interested in the passenger side quarter.
Let me know what it looks like when you get it out.

Eagle1, I have one that is already cut off the car. I'll need to get check one area on the lower rear. It has some bondo in that section so I'll pull it out and see what's going on underneath of it.

Thanks
David

Banditboy21 · « **Reply #5 on:** January 09, 2007, 04:32:47 PM »

ineed the trunk hinge area that always rots out the whole panel if u have it and possibly the drivers side floor

Crzy4my10th · « **Reply #6 on:** January 09, 2007, 06:03:54 PM »

Darn it! I just cut thru one to pull the quarters. Had I known I would have drilled out the spot welds.

Anyway, I got three more cars I can pull from. How soon do you need them?

Thanks
David

dblhh · « **Reply #7 on:** January 09, 2007, 07:19:12 PM »

If you have another rust-free passenger rear quarter, I might be interested. I only need the lower portion.

flstc89 · « **Reply #8 on:** January 09, 2007, 07:25:13 PM »

I am looking for front fenders for a 77-78 trans am, also quarter panels. My right quarter has rust in the lower rear section. So I really only need a patch.

Crzy4my10th · « **Reply #9 on:** January 09, 2007, 07:51:46 PM »

I've got a few quarters that have good metal on the lowers. I'll check them out tomorrow.

Thanks guys
David

stubes · « **Reply #10 on:** January 10, 2007, 11:01:10 PM »

i am kind of curious as to where you are located so i can figure if pickup is doable or not

Crzy4my10th · « **Reply #11 on:** January 11, 2007, 06:15:55 AM »

Stubes, I'm located in FL just outside Tampa.

David

ben alt · « **Reply #12 on:** January 12, 2007, 07:22:53 PM »

do you have the floor pans that are right under the rear seat area.

Crzy4my10th · « **Reply #13 on:** January 12, 2007, 08:29:51 PM »

Ben alt, I do have set of seat pans. I'll get some pictures up this weekend.

TO ALL OTHERS! I will be gettting back with you all. More than likely this weekend. I've been working out at CentCom ( Central Command) here at MacDill AirForce base. It's painfully slow going with all the security measures in place at the facility and it's taking up all my time.

Thanks
David

Eagle 1 · « **Reply #14 on:** January 12, 2007, 09:09:16 PM »

Thanks Crzy, just let me know about that qp when you get time.